NetBSD on t5730 - bird_dip

とりあえず NetBSD/i386 5.01 を USB 接続 CD-ROM からインストールしてみた。
- BIOS 設定で USB キーボードを有効にしておくと、インストーラの途中で PS/2 キーボードで入力できなくなった。

1st boot device で USB を有効にしていると、接続されているデバイスから起動できなくてもフラッシュからの起動に移行しない(?)。
二次記憶が HDD ではなく、フラッシュメモリ(1G)なので swap は無し。/tmp は mfs とした。/var や /home、/pkg 辺りをどうするかは検討中。
bcbench を走らせて見ると pi, e とも 12 秒台で、手元の ThinkPad X31 に近い性能か。

とりあえず、適当な設定をした状態での dmesg.

NetBSD 5.0.1 (GENERIC) #0: Thu Jul 30 01:39:11 UTC 2009
Welcome to NetBSD!
bird$ df
Filesystem 512-blocks Used Avail %Cap Mounted on
/dev/wd0a 1940190 983070 860112 53% /
mfs:164 509006 2 483554 0% /tmp
kernfs 2 2 0 100% /kern
ptyfs 2 2 0 100% /dev/pts
procfs 8 8 0 100% /proc
/dev/sd0a 38461020 8 36537964 0% /mnt
bird$ dmesg
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
NetBSD 5.0.1 (GENERIC) #0: Thu Jul 30 01:39:11 UTC 2009
builds@b8.netbsd.org:/home/builds/ab/netbsd-5-0-1-RELEASE/i386/200907292356Z-obj/home/builds/ab/netbsd-5-0-1-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 991 MB
avail memory = 962 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Hewlett-Packard hp t5730 ( )
mainbus0 (root)
cpu0 at mainbus0 apid 0: AMD 686-class, 997MHz, id 0x60fc2
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 21, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId , AslId
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 32-bit timer
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
UAR1 (PNP0501) at acpi0 not configured
pckbc1 at acpi0 (PS2K, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
acpitz0 at acpi0 (THRM): critical 100.0C, passive cooling
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1002 product 0x7910 (rev. 0x00)
ppb0 at pci0 dev 1 function 0: vendor 0x1002 product 0x7912 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 5 function 0: vendor 0x1002 product 0x791f (rev. 0x00)
vga1: WARNING: ignoring 64-bit BAR @ 0x10
vga1: WARNING: ignoring 64-bit BAR @ 0x18
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
ppb1 at pci0 dev 4 function 0: vendor 0x1002 product 0x7914 (rev. 0x00)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci2 dev 0 function 0: Broadcom BCM5787M Gigabit Ethernet
bge0: interrupting at ioapic0 pin 16
bge0: ASIC BCM5754/5787 A2 (0xb002), Ethernet address 00:23:xx:xx:xx:xx
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5754/5787 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ohci0 at pci0 dev 19 function 0: vendor 0x1002 product 0x4387 (rev. 0x00)
ohci0: interrupting at ioapic0 pin 16
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 19 function 1: vendor 0x1002 product 0x4388 (rev. 0x00)
ohci1: interrupting at ioapic0 pin 17
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
ohci2 at pci0 dev 19 function 2: vendor 0x1002 product 0x4389 (rev. 0x00)
ohci2: interrupting at ioapic0 pin 18
ohci2: OHCI version 1.0, legacy support
usb2 at ohci2: USB revision 1.0
ohci3 at pci0 dev 19 function 3: vendor 0x1002 product 0x438a (rev. 0x00)
ohci3: interrupting at ioapic0 pin 17
ohci3: OHCI version 1.0, legacy support
usb3 at ohci3: USB revision 1.0
ohci4 at pci0 dev 19 function 4: vendor 0x1002 product 0x438b (rev. 0x00)
ohci4: interrupting at ioapic0 pin 18
ohci4: OHCI version 1.0, legacy support
usb4 at ohci4: USB revision 1.0
ehci0 at pci0 dev 19 function 5: vendor 0x1002 product 0x4386 (rev. 0x00)
ehci0: applying AMD SB600/SB700 USB freeze workaround
ehci0: interrupting at ioapic0 pin 19
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: ohci0 ohci1 ohci2 ohci3 ohci4
usb5 at ehci0: USB revision 2.0
piixpm0 at pci0 dev 20 function 0
piixpm0: vendor 0x1002 product 0x4385 (rev. 0x14)
piixpm0: interrupting at SMIpiixpm0: polling
iic0 at piixpm0: I2C bus
ixpide0 at pci0 dev 20 function 1
ixpide0: ATI Technologies IXP IDE Controller (rev. 0x00)
ixpide0: bus-master DMA support present
ixpide0: primary channel configured to compatibility mode
ixpide0: primary channel interrupting at ioapic0 pin 14
atabus0 at ixpide0 channel 0
ixpide0: secondary channel configured to compatibility mode
ixpide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at ixpide0 channel 1
azalia0 at pci0 dev 20 function 2: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 16
azalia0: host: 0x1002/0x4383 (rev. 0), HDA rev. 1.0
pcib0 at pci0 dev 20 function 3
pcib0: vendor 0x1002 product 0x438d (rev. 0x00)
ppb2 at pci0 dev 20 function 4: vendor 0x1002 product 0x4384 (rev. 0x00)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled
pchb1 at pci0 dev 24 function 0
pchb1: vendor 0x1022 product 0x1100 (rev. 0x00)
pchb2 at pci0 dev 24 function 1
pchb2: vendor 0x1022 product 0x1101 (rev. 0x00)
pchb3 at pci0 dev 24 function 2
pchb3: vendor 0x1022 product 0x1102 (rev. 0x00)
amdtemp0 at pci0 dev 24 function 3
amdtemp0: AMD CPU Temperature Sensors (K8: core rev DH-G2, socket S1)
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
azalia0: codec[3]: Realtek ALC262 (rev. 2.2), HDA rev. 1.0
audio0 at azalia0: full duplex, independent
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
uhub5 at usb5: vendor 0x1002 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub5: 10 ports with 10 removable, self powered
umass0 at uhub5 port 3 configuration 1 interface 0
umass0: vendor 0x05e3 USB TO IDE, rev 2.00/0.33, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: disk fixed
sd0: fabricating a geometry
sd0: 19077 MB, 19077 cyl, 64 head, 32 sec, 512 bytes/sect x 39070080 sectors
sd0: fabricating a geometry
wd0 at atabus0 drive 0: <1GB ATA Flash Disk>
wd0: drive supports 1-sector PIO transfers, LBA addressing
wd0: 977 MB, 1986 cyl, 16 head, 63 sec, 512 bytes/sect x 2001888 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0(ixpide0:0:0): using PIO mode 4, Ultra-DMA mode 4 (Ultra/66) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
bird$