VIA EPIA-M

秋葉原エレクトリックパーツに注文したタッチパネル付液晶モニタ+PC が届いた。とりあえず電源投入テストだけ。ファン音がうるさい。Award BIOS なのか。モニタ側につながる USB とシリアルはシリアルがタッチパネル制御用なのかな。USB は単なる延長/ハブなのか。

でもって NetBSD/i386-5.0.2 での dmesg.

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
2006, 2007, 2008, 2009
The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.

NetBSD 5.0.2 (GENERIC) #0: Sat Feb 6 17:53:27 UTC 2010
builds@b7.netbsd.org:/home/builds/ab/netbsd-5-0-2-RELEASE/i386/201002061851Z-obj/home/builds/ab/netbsd-5-0-2-RELEASE/src/sys/arch/i386/compile/GENERIC
total memory = 223 MB
avail memory = 208 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
VIA Technologies, Inc. VT8623-8235 ( )
mainbus0 (root)
cpu0 at mainbus0: IDT/VIA 686-class, 999MHz, id 0x694
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId , AslId
LNKB: ACPI: Found matching pin for 0.20.INTA at func 0: 12
LNKB: ACPI: Found matching pin for 0.13.INTA at func 0: 12
LNKA: ACPI: Found matching pin for 0.16.INTA at func 0: 11
LNKB: ACPI: Found matching pin for 0.16.INTB at func 1: 12
LNKC: ACPI: Found matching pin for 0.16.INTC at func 2: 10
LNKD: ACPI: Found matching pin for 0.16.INTD at func 3: 5
LNKA: ACPI: Found matching pin for 0.17.INTA at func 1: 255
LNKC: ACPI: Found matching pin for 0.17.INTC at func 5: 10
LNKA: ACPI: Found matching pin for 0.18.INTA at func 0: 11
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Safe" frequency 3579545 Hz quality 900
ACPI-Safe 24-bit timer
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
FDC0 (PNP0700) at acpi0 not configured
UAR1 (PNP0501) at acpi0 not configured
UAR2 (PNP0501) at acpi0 not configured
LPT1 (PNP0400) at acpi0 not configured
pckbc1 at acpi0 (PS2K, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x1106 product 0x3123 (rev. 0x00)
agp0 at pchb0 (v2): aperture at 0xd0000000, size 0x10000000
ppb0 at pci0 dev 1 function 0: vendor 0x1106 product 0xb091 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: vendor 0x1106 product 0x3122 (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
fwohci0 at pci0 dev 13 function 0: vendor 0x1106 product 0x3044 (rev. 0x80)
fwohci0: interrupting at irq 12
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:40:63:50:00:00:a4:cc
fwohci0: Phy 1394a available S400, 2 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
uhci0 at pci0 dev 16 function 0: vendor 0x1106 product 0x3038 (rev. 0x80)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 16 function 1: vendor 0x1106 product 0x3038 (rev. 0x80)
uhci1: interrupting at irq 12
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 16 function 2: vendor 0x1106 product 0x3038 (rev. 0x80)
uhci2: interrupting at irq 10
usb2 at uhci2: USB revision 1.0
ehci0 at pci0 dev 16 function 3: vendor 0x1106 product 0x3104 (rev. 0x82)
ehci0: interrupting at irq 5
ehci0: dropped intr workaround enabled
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
pcib0 at pci0 dev 17 function 0
pcib0: vendor 0x1106 product 0x3177 (rev. 0x00)
viaide0 at pci0 dev 17 function 1
viaide0: VIA Technologies VT8235 ATA133 controller
viaide0: bus-master DMA support present
viaide0: primary channel configured to compatibility mode
viaide0: primary channel interrupting at irq 14
atabus0 at viaide0 channel 0
viaide0: secondary channel configured to compatibility mode
viaide0: secondary channel interrupting at irq 15
atabus1 at viaide0 channel 1
auvia0 at pci0 dev 17 function 5: VIA Technologies VT8235 AC'97 Audio (rev 0x50)
auvia0: interrupting at irq 10
auvia0: ac97: VIA Technologies VT1616i codec; headphone, 18 bit DAC, 18 bit ADC, KS Waves 3D
auvia0: ac97: ext id 1c5
audio0 at auvia0: full duplex, mmap, independent
vr0 at pci0 dev 18 function 0: VIA VT6102 (Rhine II) 10/100 Ethernet
vr0: interrupting at irq 11
vr0: Ethernet address: 00:40:xx:xx:xx:xx
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface
ukphy0: OUI 0x0002c6, model 0x0032, rev. 8
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
vendor 0x158f product 0x0010 (miscellaneous bridge, revision 0x02) at pci0 dev 20 function 0 not configured
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
ieee1394if0: bus manager 0 (me)
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x1106 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x1106 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
umass0 at uhub0 port 2 configuration 1 interface 0
umass0: USB to IDE USB to IDE, rev 1.01/0.23, addr 2
umass0: using ATAPI over Bulk-Only
atapibus0 at umass0: 2 targets
cd0 at atapibus0 drive 0: cdrom removable
wd0 at atabus0 drive 0:
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 19077 MB, 38760 cyl, 16 head, 63 sec, 512 bytes/sect x 39070080 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(viaide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio1 at pad0: half duplex
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)